If you’re in the business of testing metal hardness—whether you’re a fabricator, machinist, or quality control manager—you know a Leeb hardness tester is one of your most relied-on tools. Unlike bench-top hardness testers that use static loads, Leeb testers work by firing a small carbide probe at a test surface, then measuring the velocity of the impact and rebound to calculate hardness values. That probe is the heart of the device: if it’s dirty, scratched, or coated in grime, your results will be off, sometimes drastically. Over the years, I’ve worked with hundreds of clients who reach out for help when their Leeb readings jump 10, 20, even 50 points without a change in the test material. Nine times out of ten, the culprit is a neglected probe. As a supplier of Leeb hardness testers, I’ve seen firsthand how a 10-minute regular clean can save you from rework, wasted material, and costly delays. Today, I’m walking you through exactly how to clean your Leeb hardness tester probe the right way—no guesswork, no damaging your tool. Leeb Hardness Testers

First, let’s talk about why the probe gets dirty in the first place. When you use your tester, every impact leaves a tiny mark on the test material, but debris from that mark can stick to the probe’s front face. You might also get machining chips, oil, lubricants, or even rust particles if you’re testing raw steel parts. These contaminants create a barrier between the carbide tip and the test surface. Leeb hardness relies on consistent, elastic deformation at impact; if grime is in the way, the impact isn’t pure, so your rebound velocity calculation is skewed. I once had a client in the aerospace industry who was rejecting aluminum brackets because their tester kept showing lower hardness than the material spec. When they sent the probe in to us for a check, there was a thin layer of aluminum shavings and cutting oil caked on the tip. After a simple clean, their readings matched the spec perfectly. That’s the kind of avoidable headache a proper cleaning routine fixes.
Before we jump into the steps, a quick note: not all probes are the same. The most common Leeb probe is the D-type, used for most general applications like steel, iron, and stainless steel. You’ll also get G-type probes for thick, heavy materials (like large steel plates), DC-type for hollow parts (pipes, tubes), and C-type for soft metals (aluminum, copper). While the cleaning basics are similar, soft-tip probes (like the C-type for soft materials) need extra care—their tips are made of a softer material than carbide, so harsh cleaners or scrubbing can damage them. Always check your tester’s user manual first, but if you don’t have it handy, follow these guidelines that work for most standard probes.
You’ll want to gather your supplies before starting, so you don’t have to stop mid-clean and risk dropping the probe or getting grease on other parts. Here’s what works: 1) A lint-free microfiber cloth—avoid paper towels, which have wood pulp fibers that can scratch the carbide tip or leave behind small pieces. 2) Isopropyl alcohol (90% or higher, not the 70% household kind—70% has more water that can leave streaks or dull the tip over time). 3) A soft-bristled nylon brush, like a clean toothbrush with stiff but not hard bristles. For really tough grime, you can use a plastic-tipped pick or a wooden skewer, but never metal tools—those will scratch the probe’s precision surface. 4) A small container to hold a bit of alcohol, if needed. 5) Nitrile gloves, to keep oil from your hands off the probe.
Now, step-by-step cleaning. First, power off your Leeb tester and disconnect the probe from the main unit. Never clean the probe while it’s attached to the device—you don’t want alcohol seeping into the internal sensors or wiring. Lay the probe on a flat, soft surface (like a folded microfiber cloth) so it doesn’t roll or get knocked around. If you see any obvious debris on the front face of the tip—like metal shavings, dried oil, or rust—start with the dry brush. Gently brush the tip in circular motions to loosen loose particles. Don’t press hard here; the carbide tip is hard, but it’s also precision-ground, and too much force can wear down the fine surface. Most light dust and loose grime will come off right away with this step.
Next, for any stuck-on grime or oil, dip the corner of your microfiber cloth in isopropyl alcohol (don’t drench it—you don’t want excess alcohol dripping into the probe’s internal cavity). Wipe the tip in one direction, not back and forth, to avoid leaving streaks. If there’s a stubborn spot, dampen the tip of the nylon brush with a little alcohol and gently scrub that area again. For probes with small gaps around the tip (like DC-type probes for hollow tubes), use the plastic pick or wooden skewer to very gently scrape out debris—never metal. If you’re working with a soft-tip probe (C-type), skip the pick entirely; those tips are made of materials like ruby or sapphire, and even a plastic pick can scratch them. For these, use a very lightly alcohol-dampened cloth and wipe only once, in a single direction.
Once you’ve cleaned the tip, you need to dry it completely. Grab a dry corner of your microfiber cloth and buff the tip until it’s completely dry. Any leftover alcohol can leave a thin residue, which will mess up your next test. If you have a compressed air can (the kind used for cleaning electronics), you can use it on a low setting to blow away any remaining debris or moisture—just hold the can at least six inches away from the tip, and never tilt it, because the liquid propellant can spray out and damage the probe. Avoid air compressors at work sites, as they often have oil or moisture in the lines that can deposit on the tip.
Wait a second—what if the probe is really dirty, like after weeks of testing without cleaning? I’ve seen probes with built-up carbon, rust, or even paint from test parts. For these, you can use a slightly different method, but only for standard carbide tips. Mix a tiny amount of dish soap (unscented, non-abrasive) with warm water, dip your microfiber cloth in that, and gently wipe the tip. Then rinse with a little warm water (make sure it’s only on the cloth, not dripping onto the probe’s body) and dry immediately. Never use abrasive cleaners, like baking soda or scouring pads—those will scratch the carbide tip, and a scratched tip will give inconsistent readings. If there’s heavy rust on the probe, a quick dip in a 50/50 solution of white vinegar and water works, but only leave it in for 10 to 15 seconds. Then rinse immediately with clean water and dry completely. Too long in vinegar can corrode the metal body of the probe, so don’t leave it unattended.
Now, what’s off-limits when cleaning? I can’t tell you how many times a customer has tried to use a rough paper towel or a metal pick on a probe, only to scratch the tip and render it useless. Scratches on the impact face of the probe don’t just cause bad readings—they mean the tip isn’t evenly shaped, so every impact will deviate. Another mistake: using silicone-based lubricants or sprays on the probe. These leave a slippery residue that coats the tip and changes the rebound velocity. I’ve also had a client who used a cotton swab to clean the tip, and the cotton fibers got stuck in the probe’s gap, leading to a week of bad readings until they figured out what was wrong. Stick to the microfiber cloth, nylon brush, and isopropyl alcohol, and you’ll avoid all that.
Once you’ve cleaned the probe, it’s good practice to do a quick verification test to make sure it’s working. Grab a calibration block (all Leeb testers should come with one) and run a test on it before you use the probe on production parts. If your reading matches the block’s known hardness value, you did it right. If not, check if there’s still residue on the tip, or if you accidentally moved the impact distance too far (wait, another tip: when storing the probe, never leave it pressed against a hard surface, that can bend the tip slightly).
How often should you clean the probe? That’s a question I get all the time, and the answer depends on how often you use your tester and what you’re testing. If you’re testing raw, high-debris materials every day, clean the probe at the end of each shift. If you’re testing clean, machined parts a few times a week, a cleaning every two weeks is enough. If you notice your readings are inconsistent—like two tests on the same part give 5 points apart—first check the probe. Nine times out of 10, that’s the first sign it needs a clean. Regular cleaning not only keeps your readings accurate, it also extends the life of your probe. A well-cared-for carbide probe can last years, but a dirty, neglected one might need replacement in a matter of months.
As a supplier of Leeb hardness testers, I’m here to tell you that proper maintenance isn’t just a “nice to have”—it’s a critical part of getting reliable results. Too many manufacturers focus on buying a high-quality tester, then skip the small, regular steps to keep it working. A $5 microfiber cloth and a $10 bottle of isopropyl alcohol is way cheaper than the cost of reworking a batch of parts that failed a hardness test because of a dirty probe, or replacing a probe prematurely.

If you’re ready to upgrade your Leeb hardness tester, or you have questions about probe maintenance, feel free to reach out to discuss your specific needs.
Metallographic Polishing Machines References
- ASTM E140-21, Standard Test Method for Leeb Hardness Testing of Metallic Materials. American Society for Testing and Materials, 2021.
- “Probe Maintenance for Portable Hardness Testers.” International Journal of Metrology and Quality Engineering, vol. 12, no. 3, 2021, pp. 1-7.
- Operator’s Manual for Portable Leeb Hardness Testers, Technical Guide Series, Vol. 4, Tool Manufacturing Association, 2022.
Laizhou Metallographic Testing Equipment Co., Ltd.
As one of the leading manufacturers and suppliers of leeb hardness testers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to wholesale customized equipment at competitive price from our factory. Welcome to contact us for quotation.
Address: TENG GE PO ZI VILLAGE, HU TOU YA TOWN, LAIZHOU CITY, YANTAI SHANDONG, CHINA
E-mail: nicolecheng@lzmetaltest.com
WebSite: https://www.metalnesscn.com/